prostep IVIP
  • Suche
  • Drucken
  • LinkedIn
  • Xing
  • YouTube
  • Xing

Pro/ENGINEER / Creo Elements>> Solid Edge

The following settings are recommended up to Pro/ENGINEER Wildfire 5.0 / Creo Parametric 3.0 and Solid Edge ST 8.

Pro/ENGINEER – System

  • From the view of data exchange it is recommended to create models in Pro/ENGINEER with absolute accuracy from the beginning. The values should be 0.01mm or smaller.
  • The setting enable_absolute_accuracy yes needs to be included in configuration file config.pro.
  • There should be no layer named "255".
  • Components of an assembly should have names no longer than 16 characters.
  • To export mixed model structures, each model type should be saved as one part and transferred in assembly mode.
  • To reduce the neutral file size (save time at import) use "Shrinkwrap functionality" or "Simplified Representation".
  • Before export, check for highlighted menu option Info -> Geometry Checks for design problems. In Creo Parametric use File -> Prepare -> ModelCheck Geometry Check. Indicated features are likely to cause problems in the target system.
  • Delete all non-referenced geometry and external reference. Do not use any suppressed construction geometry (activate all layers).
  • If the model was created with relative accuracy, a conversion to its corresponding absolute accuracy might point out design problems.
  • Force regeneration by selecting: Set Up -> Accuracy -> Absolute -> Enter value or, in Creo Parametric, File -> Prepare -> Model Properties.
  • It is recommended to define therefore a specific start model.

Pro/ENGINEER / Creo Elements - STEP Preprocessor

  • Some STEP specific settings can be added to the configuration file config.pro:
  • With File -> Options -> Configuration Editor you can add the below mentioned settings in CREO Elements
  • With Tools -> Options... you can add the below mentioned settings in Pro/ENGINEER Wildfire 1.0, 2.0 and 3.0.
  • With Utilities -> Options... you can add the below mentioned settings in Pro/ENGINEER 2001.
  • With Utilities -> Preferences... you can add the below mentioned settings in Pro/ENGINEER 2000i².
  • The default setting for STEP export is AP203. For AP214 export the following setting needs to be added to the Pro/ENGINEER configuration file config.pro:
    • STEP_EXPORT_FORMAT AP214_IS
  • Other recommended config.pro options are:
    • intf3d_out_default_option solid
    • intf3d_out_extend_surface yes
    • intfd_out_blanked_entities no
  • To export a STEP File:
  • In Pro/ENGINEER 2001 and Pro/ENGINEER Wildfire and CREO Elements first select File -> Save a Copy... and then as Type choose STEP (*.stp). If not added in the config.pro yet, please select then Solid or Shell (for surface models) depending on the model type. The options Surface (default) and Wireframe should not be used.
  • In Pro/ENGINEER 2000i² first select File -> Export -> ExportOpts and then choose STEP. If not added in the config.pro yet, please select then Solid or Shell (for surface models) depending on the model type. The options Surface (default) and Wireframe should not be used.
  • If exporting an Assembly, choose Single File as File structure.
  • In the Options for Pro/ENGINEER STEP Export choose "Solids" and "Shells". The Single Option "Solids" exports only exact Pro/ENGINEER solids, shells and surface will not be exported.
  • To reduce file size (large STEP files cause often conversion problems because of memory limitations) export as multi STEP files with external references if post-processor supports this technology (very good results exporting to CATIA V5).

STEP File

  • No adjustment is necessary.

Solid Edge - STEP Postprocessor

  • To import a STEP file go to File -> Open, select the STEP file and go to Options. The Open File dialog box appears.
  • These are the recommended options that must be selected:
  • Generate Log File: to create a log file that contains warnings and information about the imported files. The name of the file is the .log and it is located in the same folder as the STEP file.
  • Heal and Stitch: to heal and stitch the free surfaces to create a solid body. It is not required to specify a tolerance range.
  • Simplify Geometry: replace the b-spline geometry from the model with simplified analytic geometry. This creates a smaller and more efficient model.
  • In case of an assembly it is recommended to select the same Output Folder as the one where the imported *.asm file is going to be saved, otherwise the imported *.par files will be saved in the same folder as the STEP file.
  • The New dialog box opens after choosing the STEP file. To import the model, a new part or assembly must be first created.

Solid Edge – System

  • In case of an assembly a *.cfg file is created. This one contains the Display Configurations of the model.

back

Beratung

Ihr Draht zu uns. Wir helfen gern in allen Fragen rund um Ihr Projekt oder Auswahl von Veröffentlichungen

Telefon
TELEFONHOTLINE
+49 6151 9287-336

Newsletter

Hier können sie sich für Ihre individuellen Neuigkeiten rund um prostep ivip eintragen.

Unser Blog

Hier erfahren Sie Neuigkeiten rund um prostep ivip und alle Themen, die digital transfomiert sind.

Blog

Jetzt die aktuellsten Themen lesen

Folgen Sie uns

Für noch mehr Inspirationen, News und Infos rund um prostep ivip.

LinkedInXingYouTubeTwitter

ImpressumDatenschutzRechtliches